Westward Ho

 After Washington DC, we turned our nose west and headed out with any real destination in mind.  We had a vague idea of stopping in Branson Mo for a show and Picher Oklahoma where we have family history.

A storm our first night inspired us to stop and overnight at a Walmart in Virginia, right at the border into Tennessee.

We then crossed into Kentucky and while meandering along decided to visit Mammoth Cave National Park.  There was a Thousand Trails nearby that had room, so we updated the GPS and changed course.

We were at the Thousand Trails only for two nights.  We went up to the National Park the morning of the second day and unfortunately found that all the tours of the cavern were sold out.

Oh well.  But the grounds of the National Park were quite nice and Ginger got a good workout on a nice long walk.

After Mammoth, we got back on the road and again headed west.  We then made a wrong turn and ended up on the road to St. Louis.

We hadn't planned on going to St. Louis, but figured what the heck.

We got into a Casino RV Park just across the river from the Arch.  The Casino was undergoing renovation with most of the features you'd expect in a Casino closed - Just one bar and a corner Deli for food.  We decided the Casino wasn't really for us, so we took the Metro across the river to the Arch. 

The Arch was quite fascinating and you can ride to the top in little pods and experience one of the best views we have ever seen.  

We highly recommend it.

We have had a couple of mechanical issues.  

First, our steps broke.  A rivetted part came un rivetted.  We discovered this when we were preparing to overnight in the Walmart we mentioned above.  We got some nuts and bolts from the hardware section in the Walmart and proceeded to "bush fix" the steps.  The bush fix will probably hold until we get home.

The other major thing was that passenger side mirror glass fell out of the mirror while running down the highway.  The heater wires kept it from hitting the asphalt and we managed a probable permanent fix while in St Louis.  Just in case though there is a bit of duct taped helping hold the glass in for a while.

Duct tape makes it all better

Just  as we were getting ready to leave St.. Louis, the dog decided to puke on the bed.   While we have laundry equipment on board, the stuff that needed washing was too big.  That necessitated a 1.5 hour stop at a roadside laundromat.

We eventually made it to the Oklahoma border and decided to spend two days in a Casino RV park in Quapaw just outside of Joplin.  Other than the fact that the Downstream Casino is a very fine Casino/Hotel resort with an excellent (no sewer) RV park, the reason we stopped here was to explore the town of Picher Oklahoma where we have family roots

October 9. 2021

Antenna Repair

We had our first overhead accident.

While trying to get into a gas station we went under a previously damaged canopy that had part of the roof dangling down. We heard two bangs, stopped and realized what was going on and then spent the better part of an hour manipulating the RV out of that gas station without causing further damage.

And we didn't even get any gas.

We pulled into a vacant lot and went up to see the damage. The satellite cover was stove in and the OTA TV antenna was at a weird angle.

Fortunately we were able push out the dents in the satellite dish over, but the OTA antenna was not quite so lucky.

The stem of the OTA antenna was badly fractured and because it would leak it became a high priority to replace it.

Fortunately the King Jack antenna used for OTA on Winnebagos' is not that expensive relative to other RV parts.  We got the part and sealant numbers from the Winnebago Support site (Yay! Winnebago!)

A call to King assured us that the Winnebago part was very close to their OAU200 antenna - they mentioned that they had recently dropped the height a bit on their antennas.  Ok.  Cool, ordered one from Amazon and ordered the sealant from Winnebago Parts.

The sealant was stuff we had never used before - "self leveling".  I read up on that and discovered that it is thinner than normal sealant and will flow into the area being sealed. 

One concern was the amount of effort needed get the old sealant off.  One person posted on an RV forum that it took a "couple of hours" to get the old sealant off.  So with trepidation and a new scraper knife from the local hardware store we attacked the old sealant.

We shouldn't have worried - the old sealant just slid off with the knife.  In less than 20 minutes, we had the sealant off and the area cleaned up and the screws holding the antenna on the roof exposed.

The new antenna is white since it doesn't make a lot of sense to male component of the team to have black heat holding components on the roof.  The above picture shows the difference in the heights of the antenna.  The new one is maybe 4 inches shorter.  That shouldn't make that much of a difference in the reception and we think it will be a heck of a lot less likely to get snagged by a tree limb.

We used black rubberized roof sealant to a bead along the base of the antenna and then screwed it down.  The screw pattern was almost the same - where it was different it the holes were sealed and new ones drilled.  While waiting for the black seal to set, we went inside and hooked up the inside electronics.  We decided to keep the old electronics in place since it was identical to the new stuff.  While waiting for the black seal to dry, we fired it up the antenna and watched the Olympics.  Granted we are in an "RF rich" environment, but we could not see any performance degradation from our old antenna.

After it sat for a few hours we put final sealant on it.  This was the whole to tube Nu-flex 311 self leveling white sealant we bought from Winnebago.  We applied it all to the base of the antenna and true to the advertisement, it flowed out, onto the surface and formed a wonderful  water tight seal.

What we did right and wrong:

1. Broke the damn antenna in the first place.  We need to be more careful about overhead obstructions.
2. We used the Nu-Flex 311 self leveling sealant.  Self leveling sealant is our new best friend.
3. We installed the stem that turns the antenna backwards and didn't realize it until after it was sealed.  This had no effect on the operation of the antenna and we are not going to fix it.  All it means is that the little arrow on the knob inside is pointing 180 degrees off.
4. We applied the self leveling sealant too gingerly.  We should have just quickly gooped it on.  While the sealing characteristics are not harmed, the surface of the sealant is a bit dimpled.  Not quite as pretty as Winnebago applied sealant.  But who are we going to offend - the seagulls?